Oil to Heat Pump with Underfloor Heating in Blackford, Perthshire

Case study · Blackford, Perthshire

Another Blackford home moves away from oil

Our latest Heat Geek Zero Disrupt installation is complete. We replaced this home’s external oil boiler with a Vaillant air source heat pump and kept the existing hot water cylinder.

Working with the home’s underfloor heating, the system is designed to keep the house comfortable at a flow temperature of just 40°C, and Heat Geek guarantees it will run at 419% efficiency.

Vaillant air source heat pump installed beside a house in Blackford, Perthshire, replacing an external oil boiler
The new Vaillant heat pump

At a glance

LocationBlackford, Perthshire
Old heatingExternal oil boiler
Heat pumpVaillant air source heat pump
HeatingExisting underfloor heating
Design flow temperature40°C
Hot waterExisting cylinder reused
Efficiency419%, guaranteed through Heat Geek
WarrantyFive-year manufacturer’s warranty on the heat pump
InstallationHeat Geek Zero Disrupt
Funding£9,000 Home Energy Scotland grant including the £1,500 rural uplift

The challenge

This home was heated by an external oil boiler, which meant keeping a tank topped up and paying whatever heating oil cost each winter.

The good news was the underfloor heating. A whole warm floor heats a room at a much lower water temperature than radiators need, and low temperatures are exactly where a heat pump works best.

Before

External oil boiler

Fuel delivered by tanker, with prices that change from one winter to the next.

After

Vaillant heat pump at 40°C

Over four units of heat for every unit of electricity used, with a 419% efficiency guaranteed through Heat Geek.

What we did

Out with the oil boiler

We replaced the external oil boiler with a Vaillant air source heat pump. It sits on a slab base on the gravel border beside the house, raised on anti-vibration feet, with the electrics running neatly up the wall to an isolator switch.

Neat pipework outside

Heat pump pipework running along the wall in black trunking
The pipework runs in black trunking

The pipes between the heat pump and the house run in black trunking along the wall. Everything is protected from the weather and looks tidy against the render.

Reusing the hot water cylinder

Existing hot water cylinder reused with the new heat pump, with expansion vessels above
The existing cylinder, now heated by the heat pump

Rather than replace the existing hot water cylinder, we kept it and connected it to the heat pump. That means less waste, less cost and less upheaval, which is what a Zero Disrupt installation is all about.

Controls

Vaillant heat pump controls showing a 31°C heating flow temperature
31°C flow temperature with 8.5°C outside

The Vaillant controls sit in the cupboard beside the cylinder. When this photo was taken, with 8.5°C outside, the system was heating the house with water at just 31°C.

As your local Heat Geek partner, we design every system to a guaranteed efficiency. For this home, that figure is 419%.

Funding with the Home Energy Scotland grant

The project was supported by a £9,000 Home Energy Scotland grant. That’s the standard £7,500 heat pump grant plus the £1,500 rural uplift. Homeowners can also apply for an interest-free loan on top of the grant.

Read our step-by-step guide to the Home Energy Scotland grant, or find out more on the Home Energy Scotland website.

The result

419%
guaranteed efficiency through Heat Geek
40°C
design flow temperature
4.19kWh
of heat for every 1kWh of electricity
5 years
manufacturer’s warranty on the heat pump

No more oil deliveries, warm floors running on gentle low-temperature heat, and a system guaranteed to perform.

The efficiency figure is the Heat Geek guaranteed design figure. Actual performance varies with the weather and how the home is used.

Got underfloor heating and oil? Good to know

  • Underfloor heating and heat pumps are a natural match. Because the whole floor gives out heat, it can run at low water temperatures, which is where a heat pump is most efficient.
  • Your existing cylinder may be reusable. It depends on whether it can take heat from a heat pump quickly enough, so we check it during the survey.
  • Ask what flow temperature your system is designed for. The lower it is, the more efficient the heat pump. This one is designed for 40°C.

Questions we get asked

Does underfloor heating work with a heat pump?

Yes, very well. Underfloor heating spreads gentle heat across the whole floor, so it needs lower water temperatures than radiators. That lets a heat pump run at its most efficient.

Can I keep my existing hot water cylinder?

Sometimes. A heat pump needs a cylinder that can take heat from it quickly enough, so we check yours during the survey. In this Blackford home, the existing cylinder was reused.

What does the Heat Geek efficiency guarantee mean?

Heat Geek partners design each system to a guaranteed efficiency figure. For this home it’s 419%, meaning over four units of heat for every unit of electricity used.

We’ve worked in Blackford before. Read about the £0 heat pump installation for another oil-heated home in the village.

Still heating your home with oil?

Get in touch with RCA Plumbing & Heating, your local Heat Geek partner, to find out whether a heat pump could suit your home and what funding you may be eligible for.

More heat pump case studies

See all our case studies, read about our Heat Geek heat pump installations or find out more about our heat pump installations across the Forth Valley.

LinkedIn
Facebook
Twitter
Email